ANBULL 2 Stroke 3.5HP Heavy Duty Outboard Motor Boat Engine w/Air Cooling System

Description

New 2 Stroke 3.5HP Heavy Duty Outboard Motor Boat Engine Air Cooling System
Feature:
Cylinder Scoring is a serious damage,which caused by improper use and will cost you a lot of money to repair the motor.
Features 360 degree steering rotation for reverse without gear shifting
Standard CDI ignition system for easy starting and improved performance
Superior engine Air cooling system for improved engine performance
Durable cast aluminum construction for superior corrosion protection
Start-In-Gear protection/clutch feature prohibits prop rotation while idling
Don't do the following will avoid cylinder Scoring:start the motor on bank,use the motor when it stop coming out of water
Even if you want test the motor, it should be done in the river!
When there is no water coming out from the motor,please stop using it immediately ,then check the impeller of Water pump or check if the water outlet has been blocked.
Item specifics:
Condition:New
Overall length: 92CM
Overall widteh: 36.5cm
Overall height: 22cm
Transom height: 42cm
Full throttle perating range: 4000-5000r/min
Maximum output: 2.5kw(3.5HP)
Speed: 20km/h(four people)
Type: 2-stroke
Ignition system: CDI system
Starting system: Manual start
Staring carburetion system: Choke start
Propeller mark: 7-1/45-A(inch)
The engine and the propeller ratio: 2:1
Recommended fuel: Regular unleaded gasoline
Fuel to oil ratio: 30:1
Gear ratio: 27/13
Maximum speed: 10 km / h
Built-in fuel tank: 1.3L
Fuel consumption per hour: 1.5L
The Package Include:
1 x 2 Stroke 3.5HP Heavy Duty Outboard Motor Boat Engine KiT
Announcements:
After in the sea water or turbid water cruising
Use the fresh water cleaning the outboard motor
With the moderate velocity circulating the engine, cool off the water chanel with fresh water.
Before completely running out cooling water, don't put the outboard motor outside. Otherwise the water cam pass the exhaust port to enter the air cylinder, from that will cause the engine breakdown.
The engine should deposit in the aridity and ventilated well place, avoid exposing directly in the sunshine.
Before the long term storing,you should run out of the gasoline in the fuel tank.
How to start the engine:
Plug the emergency turn-off cable plate in the switch groove.
Plug the oil inlet plug for transferring fuel in the Fuel tank socket.
Plug the oil outlet plug in the tubing socket of motor's bottom.
Spin and loose the venting screw in the fuel tank cap in a counter clockwise direction.
Extrude the pump a few times until the area is full with fuel and the pump goes hard.
Pull shift handle to neutral position.
Turn throttle handle to "start" .
When the engine cooled,puII out the choke valve to increase the concentration of combustible mixture gas and be more convenient and easier to start.
PuII the starting handle, untiI the initiator of the claw and the flywheel plate mesh.
After the engine runs,idle operate it for 2 to 3 minutes to warm up,then pull all the choke valve to the initial position.
After the engine runs, check cooled water stablely flows or not. If there's no water or stable flowing, turn off the engine and seek for the reason.
During running, hang up the turn-off rope in your wrist or belt to ensure sailing safety.
Note:
About the noise: all the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon.
The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same whenone person on it or 4 people on it . Customer who has high expectations on speed, please be noticed.
It can be marched with inflatable boats, rubber boats or fishing boats.
Necessary: you have to prepare a boat-motor stand or Hanging board on your boat.
Two strokes 3.5 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode
Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours)
Our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear before use !!!
Strictly for professional use only